Research overview
Research overview
Source: Dong-Woo Cho (POSTECH)

3D printed stents treat inflammation

Researchers have produced biodegradable stents with esophageal-derived bioink to directly treat radiation esophagitis.

Radiation esophagitis, characterized by the inflammation of the esophagus, is the most common acute adverse effect of radiation therapy that causes swallowing problems. This eventually causes dehydration and leaves the body unfit for further treatment. Unfortunately, no direct cure currently exists for patients suffering from such conditions. To this, a POSTECH research team has developed esophageal stents that biodegrade in the body using 3D printers, opening up the possibility of treating the condition.

A joint research team led by Professor Dong-Woo Cho and Ph.D. candidate Suhun Chae in the Department of Mechanical Engineering at POSTECH and Dr. Dong-Heon Ha of EDmicBio, Inc. has together produced biodegradable stents with esophageal-derived bioink to directly treat radiation esophagitis and verified their therapeutic effects in animal models.

Various treatment methods are being developed to treat cancer, but radiation therapy is still one of the common treatments along with surgery and chemotherapy. If radiation esophagitis occurs during radiation therapy, treatment is limited to cataclysmic therapy that relieves the pain depending on the symptoms that appear, or inserting a stent to open the swollen esophagus to allow drinking or eating. However, these methods do not treat the damaged tissues directly.

The research team first produced bioink that removed cell components from esophageal tissues and extracted only extracellular matrix through the decellularization process. They produced a dumbbell-type stent that can carry this bioink using a 3D printing system. By inserting this stent into the inflamed esophagus of an animal, they confirmed that it promotes tissue regeneration while mitigating inflammatory reactions.

"The effectiveness of treatment is negated if proper nutrition cannot be delivered due to the pain," explained Dong-Woo Cho who led the study. He added, "If this esophageal stent implantation is applied clinically, we expect that the patients will have better prognosis and higher quality of life."

The research was published in Biomaterials.

Subscribe to our newsletter

Related articles

3D printed oesophageal stents to revolutionize cancer treatment

3D printed oesophageal stents to revolutionize cancer treatment

World-first 3D printed oesophageal stents developed by the University of South Australia could revolutionize the delivery of chemotherapy drugs.

3D-printed bioresorbable airway stent

3D-printed bioresorbable airway stent

Researchers are using 3D printing to produce a new type of bioresorbable airway stent. This could greatly simplify the future treatment of upper airway obstruction.

3D printed rubbery brain implants

3D printed rubbery brain implants

Engineers are working on developing soft, flexible neural implants that can gently conform to the brain’s contours and monitor activity over longer periods.

3D biocomposites can repair large bone defects

3D biocomposites can repair large bone defects

Loosening hip implants can cause major damage to the bone and a simple replacement won’t suffice to carry the load during movements. Researchers have turned to bioprinting to solve this problem.

Antibiotics embedded in 3D printed implants used to regenerate damaged bone

Antibiotics embedded in 3D printed implants used to regenerate damaged bone

Researchers have fabricated 3D scaffold implants containing antibiotics at high temperatures. These scaffolds support bone regeneration and manage the bone infections.

3D printing resins in dental devices may be toxic

3D printing resins in dental devices may be toxic

Two commercially available 3D-printable resins, which are marketed as being biocompatible for use in dental applications, readily leach compounds into their surroundings.

3D printing strong and tough hydrogels

3D printing strong and tough hydrogels

Skin and cartilage are both strong and flexible – properties that are hard to replicate in artificial materials. But a new fabrication process brings lifelike synthetic polymers a step closer.

3D printing biomedical parts with supersonic speed

3D printing biomedical parts with supersonic speed

Researchers have developed a 3D printing technique that creates cellular metallic materials by smashing together powder particles at supersonic speed.

Aerogel: the micro structural material of the future

Aerogel: the micro structural material of the future

In a research-first, scientists from Empa were able to 3D print stable well-shaped microstructures made from silica aerogels for use in biotechnology and precision engineering.

Popular articles

Subscribe to Newsletter