Fibre sensor attached to a face covering detects human breath with high...
Fibre sensor attached to a face covering detects human breath with high sensitivity and responsiveness
Source: Andy Wang

3D printed transparent fibers can sense breath

Researchers from the University of Cambridge used 3D printing techniques to make electronic fibres, each 100 times thinner than a human hair, creating sensors beyond the capabilities of conventional film-based devices.

The fibre printing technique can be used to make non-contact, wearable, portable respiratory sensors. These printed sensors are high-sensitivity, low-cost and can be attached to a mobile phone to collect breath pattern information, sound and images at the same time.

First author Andy Wang, a PhD student from Cambridge’s Department of Engineering, used the fibre sensor to test the amount of breath moisture leaked through his face covering, for respiratory conditions such as normal breathing, rapid breathing, and simulated coughing. The fibre sensors significantly outperformed comparable commercial sensors, especially in monitoring rapid breathing, which replicates shortness of breath.

While the fibre sensor has not been designed to detect viral particles, since scientific evidence increasingly points to the fact that viral particles such as coronavirus can be transmitted through respiratory droplets and aerosols, measuring the amount and direction of breath moisture that leaks through different types of face coverings could act an indicator in the protection ‘weak’ points.  

The team found that most leakage from fabric or surgical masks comes from the front, especially during coughing, while most leakage from N95 masks comes from the top and sides with tight fittings. Nonetheless, both types of face masks, when worn properly, help to weaken the flow of exhaled breath. “Sensors made from small conducting fibres are especially useful for volumetric sensing of fluid and gas in 3D, compared to conventional thin-film techniques, but so far, it has been challenging to print and incorporate them into devices, and to manufacture them at scale,” said Dr Yan Yan Shery Huang from Cambridge’s Department of Engineering, who led the research.

3D printed transparent fibers can sense breath
Source: Science Advances (2020). DOI: 10.1126/sciadv.abd1882

Huang and her colleagues 3D printed the composite fibres, which are made from silver and/or semiconducting polymers. This fibre printing technique creates a core-shell fibre structure, with a high-purity conducting fibre core wrapped by a thin protective polymer sheath, similar to the structure of common electrical wires, but at a scale of a few micrometres in diameter.

In addition to the respiratory sensors, the printing technique can also be used to make biocompatible fibres of a similar dimension to biological cells, which enables them to guide cell movements and ‘feel’ this dynamic process as electrical signals. Also, the fibres are so tiny that they are invisible to the naked eye, so when they are used to connect small electronic elements in 3D, it would seem that the electronics are ‘floating’ in mid-air. “Our fibre sensors are lightweight, cheap, small and easy to use, so they could potentially be turned into home-test devices to allow the general public to perform self-administered tests to get information about their environments,” said Huang.

The team looks to develop this fibre-printing technique for a number of multi-functional sensors, which could potentially detect more breath species for mobile health monitoring, Internet of Things or for bio-machine interface applications.

The research was reported in the journal Science Advances.

Subscribe to our newsletter

Related articles

Wearable sensor tracks biochemical data

Wearable sensor tracks biochemical data

Scientist are developing a patch that monitors the sweat of high performance athletes for medical information.

Wearable sensor for patients with inflammatory bowel disease

Wearable sensor for patients with inflammatory bowel disease

Researchers have designed a wearable device that monitors sweat for biomarkers that could signal flare-ups of inflammatory bowel disease (IBD).

Patches detect when a viral disease is getting worse

Patches detect when a viral disease is getting worse

Xsensio has been awarded CHF 1.8 million in EU funding to adapt its Lab-on-Skin sensing patches so that they can detect when a viral illness like the flu or COVID-19 is about to get worse.

Smartwatch turns into biochemical monitoring system

Smartwatch turns into biochemical monitoring system

Engineers have designed a thin adhesive film that could upgrade a consumer smartwatch into a powerful health monitoring system.

A wearable COVID-19 early warning system

A wearable COVID-19 early warning system

A remote early warning system for the detection of COVID-19 symptoms among frontline medical staff is showing promising results.

3D printed sensor invented for wearables

3D printed sensor invented for wearables

Researchers have utilized 3D printing and nanotechnology to create a durable, flexible sensor for wearable devices to monitor everything from vital signs to athletic performance.

3D printing helps form wearable sensor

3D printing helps form wearable sensor

Researchers have developed a highly sensitive wearable pressure sensor for health monitoring applications and early diagnosis of diseases.

Activity trackers help manage diabetes

Activity trackers help manage diabetes

Patients with diabetes and cardiovascular disease who used wearable step-counting devices have shown small-to-medium improvements in physical activity.

Blood and sweat take training app to the next level

Blood and sweat take training app to the next level

Researchers have have developed a multifaceted measuring technology that is able to detect a number of conditions in the human body.

Popular articles