Diagnostic for Liquid Metal Jetting 3D printing

Researchers at Lawrence Livermore National Laboratory (LLNL) are developing a diagnostic tool that can determine the quality of metal droplets and monitor Liquid Metal Jetting (LMJ) prints in real-time.

In LMJ, tiny molten metal droplets are ejected from a nozzle at high speeds to 3D print a part in layers, similar to inkjet printers on the consumer market. Unlike laser-based metal 3D printing processes, the technology doesn’t require metal powder, which can be hazardous to handle and wasteful of material. Diagnostics used today to ensure high-quality LMJ prints largely rely on high-speed videography, which requires expensive equipment, can be difficult to set up and generates large amounts of data. While adequate for evaluating a few seconds of a test printing, it isn’t a feasible solution for longer builds.

Researchers at Lawrence Livermore National Laboratory (LLNL) are attempting to solve the problem with a new diagnostic tool that can determine the quality of metal droplets and monitor LMJ prints in real-time. The approach uses low frequency, electromagnetic near-field detection to capture metal droplet dynamics that, when combined with simulation, provides information on droplet features based on signal amplitude and phase alone.

The researchers said the ability to characterize the droplets using just one parameter significantly reduces the amount of necessary data, making processing and feedback of longer-term LMJ prints possible.

“Our results demonstrate that in situ monitoring of Liquid Metal Jetting is possible with millimeter-wave detection methods,” said lead author and LLNL engineer Tammy Chang. “This is exciting because it means we could replace computationally expensive high-speed, high-resolution optical diagnostics to enable real-time performance evaluation and feedback control, to ensure high quality printed metal parts.”

With the new technique, they discovered large-scale trends such as print variation and anomalies at the nozzle, as well as micro-level attributes about the droplets, including size, position and dynamics. The team used electromagnetic simulations to model droplet properties, allowing the team to understand the physics of the electromagnetic scattering and how variations in the magnitude and phase of the detected signals affected droplet features, Chang said.

The result of the research is a “compact and non-invasive” diagnostic able to distinguish droplets in LMJ machines at higher print rates than possible before, as well as the capability to detect additional features of the print system, researchers said. The ability to capture droplet properties based on one parameter alone ultimately shows promise for feedback systems in which rapid, real-time processing can be used to adjust print settings and guarantee part quality, they concluded.

“Getting a clean ejection of a single drop that falls straight down is key to achieving good print quality,” said LLNL engineer Andy Pascall, a co-author on the paper. “High-speed videography works well in a lab-scale environment where we are testing new print parameters, but will never work in production. The millimeter-wave diagnostic is a huge improvement because it can be integrated into the printer, doesn’t require optical access and provides data that can be analyzed in real-time to determine if high-quality droplets are being generated. This type of diagnostic will be very useful in a production environment.”

In the future, researchers said signal processing techniques could be used to correlate optical and millimeter-wave measurements and predict droplet properties based on millimeter-wave results alone. Processing efforts developed by the LLNL researchers and their collaborators are currently under review.

The work was in the Journal of Applied Physics.

Subscribe to our newsletter

Related articles

Voxel-based technique to streamline bioprinting

Voxel-based technique to streamline bioprinting

Researchers have developed a new bioprinting technique based on voxels.

3D printing nanoresonators

3D printing nanoresonators

Researchers illustrated an innovative approach to developing miniaturized and multifunctional sensors.

3D printed copper components for linear accelerators

3D printed copper components for linear accelerators

For the first time, researchers have 3D printed essential quadrupole components for linear accelerators from pure copper.

4D printing: heat shrinks printed objects

4D printing: heat shrinks printed objects

4D printing could be used to produce parts that exhibit a specific behavior only after they take their predefined shape.

Neutrons detect defects in 3D printed components

Neutrons detect defects in 3D printed components

Researchers have examined common methods used to locate defects inside components.

Self-powered wearable devices

Self-powered wearable devices

Scientists have created a 3D printing method that integrates functional and structural materials to print wearable.

AI accelerates discovery of 3D printing materials

AI accelerates discovery of 3D printing materials

A new machine learning system costs less, generates less waste, and can be more innovative than manual discovery methods.

Nanoscale lattices flow from 3D printer

Nanoscale lattices flow from 3D printer

Rice University engineers create nanostructures of glass and crystal for electronics, photonics.

Aerogel: the micro structural material of the future

Aerogel: the micro structural material of the future

Scientists from Empa were able to 3D print stable well-shaped microstructures made from silica aerogels for use in biotechnology and precision engineering.

Popular articles

Subscribe to Newsletter