Design and fabrication of a colour-sensitive model of a pixelated artificial...
Design and fabrication of a colour-sensitive model of a pixelated artificial retina via inkjet printing.
Source: Tor Vergata University of Rome

An inkjet-printed artificial retina model

Researchers from the University of Rome Tor Vergata, University of Surrey, Istituto di Struttura della Materia (CNR-ISM, Rome, Italy), Cicci Research srl., and European Molecular Biology Laboratory have developed a color-sensitive, inkjet-printed, pixelated artificial retina model.

Around 300 million people worldwide are visually impaired. Retinitis pigmentosa (RP) and age-related macular degeneration (AMD), involving deterioration of retinal photoreceptors-cells, are the leading causes of partial or total loss of vision. In the human eye, the retina contains several layers of cells including rod and cone photoreceptors that convert light into electrical signals and are responsible for night and color vision respectively. With the development of biomedical engineering in the last decades, retinal prostheses, designed to partially restore vision, have seen progress. However, those based on conventional silicon, metallic, or rigid electrodes possess poor flexibility and biocompatibility.

In recent years, photosensitive organic electronic materials have been shown to be a very promising tool, even transplanted in vivo, for transducing light stimuli to non-functioning retinas. The materials are mechanically flexible, so they are applicable to flexible and conformal substrates and can be deposited through inks. Up to now, the spectral responsivity was considered individually for one polymer semiconductor at a time in artificial retina applications. However, to contemplate color vision, pixelation of different polymers that are photosensitive to different parts of the visible spectrum (color sensitivity), mimicking those of the photoreceptors, is necessary.

Human retina, organic semiconducting polymers and bio-hybrid photovoltaic...
Human retina, organic semiconducting polymers and bio-hybrid photovoltaic device architecture.
Source: Tor Vergata University of Rome

The multidisciplinary international team demonstrated the design and fabrication of a color-sensitive model of a pixelated artificial retina where each polymer dot was deposited by inkjet-printing (Figure 1). Three types of polymer semiconductors, with spectral absorbance curves emulating those of rods, and of cones which provide color sensitivity, were deposited in a concentric layout simplifying the anatomical human retinal scheme.

The team verified that the phototransduction process from the artificial retina to a biological electrolyte solution imitating extracellular fluids found in our tissues produced electrical signals compatible with those found in retinas through a novel closed sandwich-type optoelectronic device (Figure 2). The bio-hybrid device, which combines techniques used in electrophysiology, organic photovoltaics and dye-sensitized solar cells, presents some advantages compared to conventional electrophysiological investigative systems: it is compact, easy-to-handle, transportable, with controllable size and requires a small amount of bio-electrolyte thus permitting use of tools typically found in an electronic-engineering/physics/chemistry laboratory. Photosensing through three-color pixelation allowed incoming light to be resolved both spectrally and spatially. The biocompatibility of each type of photosensitive polymer was also demonstrated.

Microscopy images of the inkjet-printed Artificial Retina and its spectral...
Microscopy images of the inkjet-printed Artificial Retina and its spectral response.
Source: Tor Vergata University of Rome

The number of pixels of the artificial retina model with distinct absorption spectra, mimicking the chromatic sensitivity of photoreceptors in the eye and interfaced with a physiological medium was 42100, the density of the artificial photoreceptors was ∼11,000 pixels/cm2 and the corresponding spatial resolution was 267 dpi (dots per inch), with pixel diameters of 95 micrometers comparable to that of a human hair (Figure 3). Future studies should compare and investigate the interaction of the artificial retina model with biological ones. Printing technologies enable placement of different materials in the locations of choice. In view of a future based on personalized medicine, and with the development of higher resolution techniques (i.e. ≤ 10 micrometers which is the diameter of human retinal photoreceptors), one could think of first imaging an individual retina and then printing the pixels so as to spatially reproduce their location.

The research was published in Scientific Reports.

Subscribe to our newsletter

Related articles

virtual.COMPAMED receives international resonance

virtual.COMPAMED receives international resonance

COMPAMED 2020 took place entirely online due to the pandemic - but still won over their audiences due to their high degree of international resonance in this format too.

A microfluidic chip system as alternative to animal experiments

A microfluidic chip system as alternative to animal experiments

Since mid-2019, the Fraunhofer IBMT has been developing an analysis platform as an alternative to animal experiments in drug development.

"Super Human Eye" works like a real one

"Super Human Eye" works like a real one

Researchers have crafted an artificial eye with capabilities close to its human model.

Fabricated corneal tissue allows closer look at how eyes heal

Fabricated corneal tissue allows closer look at how eyes heal

Researchers used a microfluidic devices to fabricate tiny strands of collagen called fibrils to help further his team’s research on the eye’s repair process.

3D printed artificial corneas similar to human ones

3D printed artificial corneas similar to human ones

Researchers have 3D printed an artificial cornea using the bioink which is made of decellularized corneal stroma and stem cells.

3D Printing living cells with unprecedented precision

3D Printing living cells with unprecedented precision

The combination of a 2Photon 3D-printer with an innovative hydrogel-based bioink allows the direct printing of 3D structures containing living cells at both the meso- and microscale.

Synthetic mucins mimic the structure of naturally occurring mucins

Synthetic mucins mimic the structure of naturally occurring mucins

Researchers have created polymers that replicate the structure of mucins, the molecules that give mucus its unique antimicrobial properties.

A conductive hydrogel for medical applications

A conductive hydrogel for medical applications

Researchers have developed a method to produce graphene-enhanced hydrogels with an excellent level of electrical conductivity.

Adaptive microelectronics reshape independently

Adaptive microelectronics reshape independently

Nanoscientists have developed adaptive microelectronics that can move independently according to sensor data and align themselves specifically for activities - possible applications in biomedicine and bioneural interfacing.

Popular articles

Subscribe to Newsletter